Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

My First IR Build

Joined
Apr 6, 2010
Messages
81
Points
0
However, this small pot looks like in fire :D
I have big wirewound pot and it gets very hot after 10 seconds...can you imagine what would happen to your small pot :D

You should buy AMC7135 regulator (one that has 4 AMC7135 chips on PCB).
That driver should give you about 1.4A but don't give it more than 4.2V.

That should be the most efficient driver for IR diodes.
You can power up your diode with only one 18650 battery that is great for portable builds.


AMC7135 1050mA Regulated Circuit Board for DIY Flashlights 10-Pack
Item #: 1885

Is what I have on order lol

As for the pot... it doesn't really get hot ever on me... Of course, that may because it is set for least resistance lol.
 





ReNNo

0
Joined
Mar 27, 2009
Messages
589
Points
0
I would prefer 1.4A for 1W diode.
1.05A is not enough for 1W diode to give you 1W of light.
 

jayrob

0
Joined
Sep 21, 2007
Messages
9,862
Points
113
By the way, I am currently pushing about 1.4 amps into mine.... If i put electrical tape directly above the die (less than a mm away, but not actually touching), it punches a hole right through it with no problem. In fact..... I have a video of it lol. Give me a moment to pull the video from my laptop and upload, I'll post it in a few minutes....

And I don't want to give up at all on this diode... I don't have money to waste lol, so I have to get something out of it.

Besides, I discussed the whole GRIN lens thing with my father-in-law (mad scientist type engineer, brilliant man), and yes, the GRIN will do what we need. As far as mounting, I'm talking to someone from a company that makes these kinds of lens, he can probably provide a solution.

I've got two diodes, so if we find a solution, I'm ready! :)

Not sure I want to buy the GRIN lens without knowing for sure if it will work out...

The one I saw was only 1.8mm in diameter, which is much smaller than the window of the diode:

Gradient Index (GRIN) Rod Lenses - Edmund Optics

I was looking at number NT64-526, which has .23mm working distance...
 
Joined
Apr 6, 2010
Messages
81
Points
0
I would prefer 1.4A for 1W diode.
1.05A is not enough for 1W diode to give you 1W of light.

True, but I'm sure there's a way to modify the circuit ever so slightly to give me that increase.

Either way, the main problem we are facing is that stupid lens. Hopefully I can figure out a way to mount it properly soon. Jay- I'm probably still going to need to order (at the very least) a heatsink from you. But, let's wait until we get the lens mounting figured out of course so we don't have issue with that. I will probably also want your glass lens assembly as well... this Aixiz acrylic isn't going to cut it.. literally lol.
 
Joined
Apr 6, 2010
Messages
81
Points
0
I've got two diodes, so if we find a solution, I'm ready! :)

Not sure I want to buy the GRIN lens without knowing for sure if it will work out...

The one I saw was only 1.8mm in diameter, which is much smaller than the window of the diode:

Gradient Index (GRIN) Rod Lenses - Edmund Optics

I was looking at number NT64-526, which has .23mm working distance...

Like I said before, I'm talking to one of the people who manufactures such things, and he can most likely provide some sort of a mount for the lens.

I'll let you know as soon as I find out
 
Joined
Nov 7, 2008
Messages
5,725
Points
0
Always be careful doing that, though... The smoke can leap backwards and put a nice film over the window or the die itself depending on what kind of diode you've got..
 
Joined
Apr 6, 2010
Messages
81
Points
0
cool so you can burn with it at point blank range without a lense?
Well if you want to get technical, when the beam is AT the die, it's extremely focused, so directly on the die you have pretty good effectiveness
Always be careful doing that, though... The smoke can leap backwards and put a nice film over the window or the die itself depending on what kind of diode you've got..

Heh funny you mention that... I actually did accidentally touch the tape to the die (in the video, the last time I burned it, right after I try again and nothing happens) It left a VERY small black spec where the tape burned onto it... Luckily I got to it quickly with isopropyl alcohol (when it had cooled down enough that is.


I HATE MY KEYBOARD..... my backspace key doesn't work anymore for some reason :(
 
Joined
Apr 6, 2010
Messages
81
Points
0
Jay, if you're still reading this post- I'll bite the bullet and grab one of those lens from Edmunds, let you know what happens.
 
Joined
Apr 6, 2010
Messages
81
Points
0
Thank you for ordering from Edmund Optics. Your order # is ******,
which you should keep in case you have any questions about your order.
Our records show that you have ordered the following:

Stock Number Quantity Price Total Description
------------------------------------------------------------------------
NT64-526 1 $39.00 $39.00 GRIN Lens 1.8mm Dia, 810nm DWL
------------------------------------------------------------------------

Subtotal: $39.00
Shipping: $10.87
Tax: $4.11
Total: $53.98
 
Joined
Apr 6, 2010
Messages
81
Points
0
Oh and that driver from hong kong finally showed up.... Hoping I can have something working by this next weekend...
 

jayrob

0
Joined
Sep 21, 2007
Messages
9,862
Points
113
Jay, if you're still reading this post- I'll bite the bullet and grab one of those lens from Edmunds, let you know what happens.

Thanks for trying that out for us!

Looking forward to the results...
 
Joined
Apr 6, 2010
Messages
81
Points
0
Ok, here is what I came up with.... Please, excuse the crude drawing, don't have my graphics software at work....

But basically, the diode is 9mm. So, I use a 9mm inside diameter copper tubing, mount the diode in. Then, get a 9mm blank washer (no hole), and drill out a hole 1.8mm thick in the center (well, maybe something like 1.85.... whatever), and slip the GRIN into that and epoxy around the outside of the lens where it touches the washer. Then I slide this assembly into the copper tubing so that the lens is on the diode. epoxy the edges of the washer. Then slide this entire assembly into the module, and use the lens in the module to finish focusing it.

That's the best I've come up with so far.



NOT TO SCALE (Obviously)
attachment.php
 

Attachments

  • Lens setup.JPG
    Lens setup.JPG
    27.8 KB · Views: 492
Joined
Apr 6, 2010
Messages
81
Points
0
Well, according to UPS, the lens should be in today.... Just need to get over to Home Depot or Lowes and grab the other items to build the mount.

I'll let everyone know how it goes, and actually will video it all and post it on my youtube.
 




Top