- Joined
- Nov 30, 2008
- Messages
- 428
- Points
- 18
Closed
Last edited:
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
WTB-Leadlight hosts
- Thread starter Swordofsalvation
- Start date
jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
Have you seen these?
http://laserpointerforums.com/laser_pointer_forums_3/forum/showthread.php?t=22561
Otherwise, I do have two LeadLight red's. (635nm) >1mW chrome pens that I would sell for $20 ea.
http://laserpointerforums.com/laser_pointer_forums_3/forum/showthread.php?t=22561
Otherwise, I do have two LeadLight red's. (635nm) >1mW chrome pens that I would sell for $20 ea.
jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
Have you seen these?
http://laserpointerforums.com/laser_pointer_forums_3/forum/showthread.php?t=22561
Otherwise, I do have two LeadLight red's. (635nm) <1mW chrome pens that I would sell for $18 ea.
http://laserpointerforums.com/laser_pointer_forums_3/forum/showthread.php?t=22561
Otherwise, I do have two LeadLight red's. (635nm) <1mW chrome pens that I would sell for $18 ea.
- Joined
- Nov 30, 2008
- Messages
- 428
- Points
- 18
alright thread closed. Thanks jayrob. Im looking into building some low powered pens for christmas presents. I need to look at costs and such.
- Joined
- Nov 30, 2008
- Messages
- 428
- Points
- 18
you will have buisness from me inthe near future. Thanks.
PS-for the pcb board, is it diffuclt to wire up the momentary switch? Ive seen some of these buttons, but never actually used them before
PS-for the pcb board, is it diffuclt to wire up the momentary switch? Ive seen some of these buttons, but never actually used them before
jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
I include a momentary switch with the pen hosts!
You will just have to get some PCB material and build a little board.
Here are some good pictures from iknitsteel:
http://laserpointerforums.com/f64/f...l-parts-included-nice-22561-5.html#post553699
You will just have to get some PCB material and build a little board.
Here are some good pictures from iknitsteel:
http://laserpointerforums.com/f64/f...l-parts-included-nice-22561-5.html#post553699
- Joined
- Nov 30, 2008
- Messages
- 428
- Points
- 18
what holds the pcb in the plastic case thing?
jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
When you get it adjusted right, just use a little glue...
Plus, the batteries will be pressing up to it's spring contact that you will solder on there.
The black plastic holder also gets a tiny dab of glue to position it.
There a little tricky until you get used to them. But not too bad if you have some basic building skills...
Plus, the batteries will be pressing up to it's spring contact that you will solder on there.
The black plastic holder also gets a tiny dab of glue to position it.
There a little tricky until you get used to them. But not too bad if you have some basic building skills...
