lazeerer
0
- Joined
- May 25, 2010
- Messages
- 3,655
- Points
- 0
Hey All,
*SOLD OUT*
If enough interest in shown I might continue to sell some more of these guys.
So if you are Interested Please Post the Milliamp "mA" Range you would most like to have.
Thank You
**0 Left**
For Sale are 6 Mini X-Drive V6's.
There are a few Pre Set Ranges you can choose From for now but there will be more Ranges If i decided to sell anymore of this Version.
All Currants are +/-10mA....
750mA
1220mA
1500mA
The 750mA is set for the NEW Mitsubishi 300mW Diodes and Works off 1x lithium-ion 3.7v cell only. This is a Safe Currant to run these diodes at.
The 1220mA is for 445nm and Runs off 2x 3.7v cells.
The 1500mA is for 445nm as well and you can use the same 2x 3.7v cells.
Driver Dimension are:
15.5mm Long x 10.3mm Wide x 1.5mm Thick.
This one will not fit inside an Axiz Module but will fit Perfect inside the Heatsink Behind the Aixiz Module that holds your diode. "Please look at Picture Bellow"
The Driver has a Set up where you can Either Attach it Directly to the Back of the Diode or Run Leads Off it to your Diode.
NO Heatsink is Required for use with this X-Drive or any of my X-Drive Drivers.
Here are some Pictures of the Driver:
On top of a USA Dime.
Connected to a diode.
Connected to the back of the Diode showing the Fit inside the Heatsink.
X-Drive Wiring Diagram.
Once all 6 are sold i will make them as i will know which set resistor to use for your Drivers and I can Reflow them all at once.
Post on Pm me.
As Always...
:thanks: For Looking.!!!
*SOLD OUT*
If enough interest in shown I might continue to sell some more of these guys.
So if you are Interested Please Post the Milliamp "mA" Range you would most like to have.
Thank You
**0 Left**
For Sale are 6 Mini X-Drive V6's.
There are a few Pre Set Ranges you can choose From for now but there will be more Ranges If i decided to sell anymore of this Version.
All Currants are +/-10mA....
750mA
1220mA
1500mA
The 750mA is set for the NEW Mitsubishi 300mW Diodes and Works off 1x lithium-ion 3.7v cell only. This is a Safe Currant to run these diodes at.
The 1220mA is for 445nm and Runs off 2x 3.7v cells.
The 1500mA is for 445nm as well and you can use the same 2x 3.7v cells.
Driver Dimension are:
15.5mm Long x 10.3mm Wide x 1.5mm Thick.
This one will not fit inside an Axiz Module but will fit Perfect inside the Heatsink Behind the Aixiz Module that holds your diode. "Please look at Picture Bellow"
The Driver has a Set up where you can Either Attach it Directly to the Back of the Diode or Run Leads Off it to your Diode.
NO Heatsink is Required for use with this X-Drive or any of my X-Drive Drivers.
Here are some Pictures of the Driver:
On top of a USA Dime.
Connected to a diode.
Connected to the back of the Diode showing the Fit inside the Heatsink.
X-Drive Wiring Diagram.
Once all 6 are sold i will make them as i will know which set resistor to use for your Drivers and I can Reflow them all at once.
Post on Pm me.
As Always...
:thanks: For Looking.!!!
Last edited:
