ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
Sold.
Last edited:
LPF Donation via Stripe | LPF Donation - Other Methods
Links below open in new window
ArcticMyst Security by Avery
Sold
- Thread starter ARG
- Start date
- Joined
- May 10, 2011
- Messages
- 1,878
- Points
- 48
Re: FS - Lots of Parts and Lasers
you posted the same pick for your waterproof green as he modules may wanna fix that bud:beer:
you posted the same pick for your waterproof green as he modules may wanna fix that bud:beer:
ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
- Joined
- May 10, 2011
- Messages
- 1,878
- Points
- 48
Lase
0
- Joined
- Apr 27, 2011
- Messages
- 757
- Points
- 0
Re: FS - Lots of Parts and Lasers
What wavelength is the he-ne?
Lase
What wavelength is the he-ne?
Lase
Last edited:
- Joined
- Mar 25, 2008
- Messages
- 1,007
- Points
- 38
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
Re: FS - Lots of Parts and Lasers
How big is the green laser?
Is the output stable or is 78 peak?
Beam diameter?
I need to replace my cheapie dying non pen green
How big is the green laser?
Is the output stable or is 78 peak?
Beam diameter?
I need to replace my cheapie dying non pen green
ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
Re: FS - Lots of Parts and Lasers
No idea, I think the 78mW is avarage, Yobresal LPM'd this for me.
The beam specs on it is amazing, it's a really tight beam, about half the size of a 532nm pen beam.
Edit: Beam is less than a mm at aperture.
How big is the green laser?
Is the output stable or is 78 peak?
Beam diameter?
I need to replace my cheapie dying non pen green
No idea, I think the 78mW is avarage, Yobresal LPM'd this for me.
The beam specs on it is amazing, it's a really tight beam, about half the size of a 532nm pen beam.
Edit: Beam is less than a mm at aperture.
Last edited:
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
Re: FS - Lots of Parts and Lasers
A little smaller than 6 inches long, and a little less than an inch wide. Sorry I can't give you a more accurate measurement, but I seem to have misplaced my digital caliper.
A little smaller than 6 inches long, and a little less than an inch wide. Sorry I can't give you a more accurate measurement, but I seem to have misplaced my digital caliper.
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
Re: FS - Lots of Parts and Lasers
Promise... last question... is it focusable?
Promise... last question... is it focusable?
ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
Re: FS - Lots of Parts and Lasers
Nope, not focusable.
Nope, not focusable.
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
Re: FS - Lots of Parts and Lasers
Just looked over the original group buy thread... I know I said it was the last question, but I lied
How much run time, ballpark, does it have on it? I mean is there any reason you're selling it? Dips in power, anything like that?
Just looked over the original group buy thread... I know I said it was the last question, but I lied
How much run time, ballpark, does it have on it? I mean is there any reason you're selling it? Dips in power, anything like that?
ARG
0
- Joined
- Feb 27, 2011
- Messages
- 6,772
- Points
- 113
Re: FS - Lots of Parts and Lasers
Well, I don't have an LPM (I keep on putting it off), but visibly it doesn't look like it has any dips in power, i'm selling it because I just ordered the REKE-500 and this laser doesn't get much use.
Ballpark run time... Around an hour, with short duty cycles, 30 second on, minute off.
Edit: From a cold start, it takes a couple of seconds to reach full power, but that's normal for KTP I think.
Well, I don't have an LPM (I keep on putting it off
), but visibly it doesn't look like it has any dips in power, i'm selling it because I just ordered the REKE-500 and this laser doesn't get much use. Ballpark run time... Around an hour, with short duty cycles, 30 second on, minute off.
Edit: From a cold start, it takes a couple of seconds to reach full power, but that's normal for KTP I think.
Last edited:
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
Re: FS - Lots of Parts and Lasers
PM Incoming
Well, I don't have an LPM (I keep on putting it off
Ballpark run time... Around an hour, with short duty cycles, 30 second on, minute off.
Edit: From a cold start, it takes a couple of seconds to reach full power, but that's normal for KTP I think.
PM Incoming
- Joined
- Mar 27, 2011
- Messages
- 14,125
- Points
- 113
Received the Yobresal GB 100mW green waterproof laser today, and just finished testing it out.
Total output is ~130mW, with about 30mW IR content.
Looks Like waterproofing lens is AR coated laser puts out ~150mW without it!
Thanks:beer:
Edit:
Have you ever tried the laser with a 3.7v battery?
Total output is ~130mW, with about 30mW IR content.
Looks Like waterproofing lens is AR coated
laser puts out ~150mW without it!Thanks:beer:
Edit:
Have you ever tried the laser with a 3.7v battery?
Last edited:
