Sale Thread: New Inexpensive 18650/cr123a Host Kit - $25 Shipped!

[ColdStl]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

I put a 445nm in one of those with 3 cr123's, a rkcstr driver, and a massive heatsink. Had to press fit the heatsink though because I couldn't get that damn bezel off.
It does make a decent host with such a huge heatsink and the different battery options. Plenty of room for different driver setups as well.
$25 is a good price.

 

[technophiliac]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

i want to buy 1x....will be using a 18650 and will most likely be paid in a week

 

[Alexizupinhea]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

Yeah, I couldn't get these crowns off either, I got a couple of these hosts myself. That part alone makes the kit worth your trouble. The crowns are also a little bit sharp, I cut my finger a little trying to get one off (very little surface cut - maybe a drop or two of blood).

Good luck getting these kits all together , and thanks for the tip about the crown - I assumed it was permanent after so long, I guess I'll give it another shot.

 

[sampson]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

Mark me down for 1x of the 18650 version. Do you PM when they're available?

 

[Helios]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

Mark me down for 1x of the 18650 version. Do you PM when they're available?

Your on the list :beer:

I will be working on them tomorrow and then PMing those on the list and sending them out in that order. I see no reason that I shouldnt be able to have several done by tomorrow night so you could realistically have it in a few days.

 

[danefex]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

pm sent

 

[sampson]

Re: Sale Thread: New Inexpensive 18650/cr123a Host Kit

Your on the list :beer:

I will be working on them tomorrow and then PMing those on the list and sending them out in that order. I see no reason that I shouldnt be able to have several done by tomorrow night so you could realistically have it in a few days.

Sounds great. I'll await your message, sir!

THanks!

 

[laserpyro]

Hey Mate Could I get one please. Just let me know how much shipping to australia is and will this fit Industrial 660nm 250mW Red Laser Diode Module Lazer Dot

 

[Helios]

Hey Mate Could I get one please. Just let me know how much shipping to australia is and will this fit Industrial 660nm 250mW Red Laser Diode Module Lazer Dot

It says its 12mm so it should assuming their listed dimensions are correct.

Ill add you to the list.

 

[laserpyro]

ok sweet

 

[bluuray]

ok put me on the list to ... ill probably get one

 

[Helios]

Teaser update:

I got the prototype heatsink made

I have since added a 445nm diode, flexdrive at 1200mA and I am waiting on the epoxy holding the battery positive contact to cure. More pictures will be added in the morning. I will also start work on the preorder hosts!

This price will not last much longer. Theres a bit more machine work required than I had anticipated and this kit and heatsink are quite large.

please excuse my camera phone

 

[rhd]

Thats looks great!

 

[sampson]

Wow.. Nice!! Can't wait to get one!!!! I've just got to decide what I want to put into it. I'm leaning towards a 400-500mw 405nm build. Damn nice work, sir! :thanks:

 

[technophiliac]

hey, do you think this aluminum heatsink is adequate enough for a 1w 445nm?.....i would usually say copper but it is turning out to be a nice host.

 

[Helios]

hey, do you think this aluminum heatsink is adequate enough for a 1w 445nm?.....i would usually say copper but it is turning out to be a nice host.

Its much more than adequate for a high power 445nm. I have one built as 445nm set at 1.3A and it doesnt even get warm after being on for a full minute. :beer: I havent tried longer but with the driver heat sinked so well the duty should be almost continuous.


For those waiting on hosts they are still in the works. I decided to make sure and build one into a working unit just to be sure there wouldnt be any unforeseen issues when you guys get your kits. Right now im just trying to figure out the best option for the battery positive terminal. It nees to be mounted on the back of the heatsink but isolated electrically from it. Right now im using the contact on the original LED driver but im open to any suggestions if you guys have any! :yh: