Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

New Linear driver! ST-DRIVE

Benm

0
Joined
Aug 16, 2007
Messages
7,896
Points
113
Diode temperature limiting would be a nice thing to have if you put it in portable hosts. I've never seen it either, though its not very difficul to build electronically... probably just a matter of mechanical work getting the sensor in good contact with the diode.
 





mpwn

0
Joined
Aug 18, 2011
Messages
284
Points
0
id be in for 2. but a i got a few questions, im new to the driver stuff :)

1. Can this driver be set at any current under 2 amps?
2. I have no idea how to set current so how do you?
3. Is shipping included in price?

Thanks
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
Yes but they come preset.
They use a low value resistor.
i can set them but the average user will not be able to change the current.
Shipping is not included, especially shipping out side the us.
Just let me know what current you want and i will try to get it close.
the forumla is simple
100/current = resistor
(100/1500= 0.066ohm)
So as you can tell the resistor is a very low value.
The diode temp monitor will take a bit of time but is doable.
but once tripped it may take around 20min for the laser to turn back on.
This is still perfect for the average noob, but could be annoying for some more advance users.
 
Last edited:
Joined
Jan 14, 2011
Messages
3,816
Points
63
It looks like you have a good seller here, Kiyou! Congratz :D

Anyway, I was looking at making my own STCS1 drivers (I usually don't push 445s higher than 1.5A anyway, so why would I need another?) and I came to the realization that using a thermistor for thermal shut off wouldn't work, because the shutdown pin doesn't work on current, it works on voltage... and the current necessary is TINY. So you would need a thermal transistor, if they exist... because you just need to cut off the VOLTAGE.
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
you can use a thermistor in a voltage divider setup to cut the voltage.
The stcs1a, is a good chip i got 50 sitting on my desk but i wanted the 2a version first.
before the months end.
If someone who has eagle want to throw the board together i will send it off to have it made.
 

mpwn

0
Joined
Aug 18, 2011
Messages
284
Points
0
aah alrite thanks, maybe you should put approximate international shipping price in original post :)

Thanks
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
I dont sell these to make much of a profit. but any one who designs a chip that using anything from st micro i can produce for much cheaper than anyone else.
Plus who ever designs it gets them fore free with limits.
idk i have gotten much better at eagle so i might just make the stcs1a version tonight.
The question now is 1 or 2 chip board.
2 chips would be 3a max.
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
Okay these are going to be for sale NOW!
i have 17 units in stock.
None have the current set once your order is placed i solder the set resistor and away it goes.
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
Yes.
VDROP Dropout voltage (VDRAIN to GND)
IO = 100 mA 0.12 - 0.16V
IO = 2 A 0.58- 0.9V
The max and worst case the vdrop will only be .9
But in most cases and when being driven at 1.5 it will be around or less than .5
 

Benm

0
Joined
Aug 16, 2007
Messages
7,896
Points
113
I guess you need to adhere to the worst case scenario for real world applications though - not that 0.9v drop is a bad figure at all. Its probably attractive for powering high powered 445s and 405s from 2 lithium cells as those 0.9 volts fit the gap very well.
 
Joined
Oct 24, 2009
Messages
2,555
Points
48
true, but thats at 2A, so for 1.6A the v drop worst case would be less.
Way better than the lm317 or the lm117 they have a vdrop total after circuit of 2.45V
 




Top