Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

My 3 Projectors for sale

Joined
May 24, 2007
Messages
3,394
Points
0
so to cut a long story short the projectors only come out twice a year, the UK meets. due to family and work i dont fire up the projectors like i used to and i havent done shows for a long time now.

it seems silly to have this expensive kit sitting round doing nothing. the plan is to sell them and build a small RGB and i can use in the house and take to meets etc...

13040016_zps48a1c1a8.jpg


13040017_zps8f80379b.jpg


all projector cases are rock solid and very well build, all the cases were built by the same place.

ok first the smallest -

outside measurements are 250mm L x 195mm W x 110mm H

inside is two 445nm diodes running at a watt each, combined through a cube and corrected via prism pair
the scanners are 20k scanners
everything is mounted on a 10mm thick ally base plate and the projector is fan cooled (with dust filter)
although there isnt one there i machined the projector aperture to take a 2inch square AR 3mm thick glass windows from edmund optics
the case is sealed using rubber draft excluder

13040018_zpse9ec9f17.jpg


13040019_zps74c71c0b.jpg


http://i187.photobucket.com/albums/x202/magicmushrooms1/13040021_zpsefea7e68.jpgimg]

[img]http://i187.photobucket.com/albums/x202/magicmushrooms1/13040023_zps03f21914.jpg


i would accept £450 for this projector



next the middle sized projector measureing 300mm L x 330mm W x 230mm H

inside is a 1000mw 532nm cni green although when metered a few years back it was doing 1.2watts.
D40 scanners although old ones, which have been modded by bill at pangolin
both lower and upper ally base plates are 12mm thick so nice and stable and good for heat sinking
there are no flex mounts in this projector, the mounts are RGB style mounts so very stable

as you can see plently of room for red and blue, its fully set up for additional colours as that was always my aim. on the lower deck are a 5v 8amp psu and 12v 8amp psu, which feeds into that connector at the rear of the green module. as you can see from the screw holes this used to have a 445 in it. there is also a laserwave 445 dichro already install in front of the green.
all holes in the base plates were done on my mill so nice and tidy.
the projector is sealed with a 3mm thick AR glass window from edmund optics and draft excluder round the case. all fans have dust filters on them.
also comes with this projector is a wind up stand and a 30m ILDA cable. stand goes up to 3m in height. the arm for the stand is not bolted to the projector in the photos incase your wondering

the projector has custom machined fan guards on it, long storey dont ask

13040026_zps14d72a7a.jpg


13040027_zps9780b608.jpg


13040028_zps8e2faf67.jpg


13040029_zpsc4a124b2.jpg


13040030_zpsd9b2eb6d.jpg


13040031_zpsf19e0695.jpg



asking £1200 for this


next is the biggest projector measuring 340mm L x 330mm W x 250mm H

inside is a 1000mw 532nm cni green although when metered at the meet it was doing 1.2watts. this module has very few hours on it, its done no shows only 2x uk meets.
D30 scanners from rob, again done no shows only 2x uk meets
both lower and upper ally base plates are 12mm thick so nice and stable and good for heat sinking
there are no flex mounts in this projector, the mounts are RGB style mounts so very stable

as you can see plently of room for red and blue, its fully set up for additional colours as that was always my aim. on the lower deck are a 5v 8amp psu and 12v 8amp psu, which feeds into that connector at the rear of the green module. there is also a laserwave 445 dichro already install in front of the green.
all holes in the base plates were done on my mill so nice and tidy.
the projector is sealed with a 3mm thick AR glass window from edmund optics and draft excluder round the case. all fans have dust filters on them.
also comes with this projector is a wind up stand and a 30m ILDA cable. stand goes up to 3m in height. the arm for the stand is not bolted to the projector in the photos incase your wondering

13040032_zps4648a843.jpg


13040034_zps365d6baa.jpg


13040035_zpsa20b4d00.jpg


13040036_zps7fcc11c8.jpg


13040037_zps8c399d03.jpg


13040038_zps89385856.jpg



again asking for £1200 for this projector


those are guide prices on all three i am open to offers on all
 





Joined
Apr 2, 2009
Messages
10,662
Points
113
Free BUMP for one of the best builders.. whoever gets these will be impressed IMO.

hak
 
Joined
May 24, 2007
Messages
3,394
Points
0
many thanks

on the building front heres how my modules look these days
13020060_zps2c1da359.jpg
 
Last edited:
Joined
Mar 23, 2011
Messages
2,095
Points
63
Very nice looking systems Andy!

I can only imagine what shipping to the US would add to the price though. It's just as well I leave it at imagine, my wallet is practically starving at the moment. :(
 
Last edited:
Joined
Dec 17, 2012
Messages
2,081
Points
63
Man I really want one of these. I just wouldnt be able to afford the whole setup with my many other prohects going on. These look beautiful though. Good luck with the sale!
 




Top