Letting go of my ILX Lightwave LDX-3207B Precision Current Source for driving your lasers!!
Initially priced at thousands; now selling only at
[highlight]US$150 shipped[/highlight]
Check out the price when new! (>$1000)
Here are some of the specs:
- Intuitive front panel
- Highly visible green LED display
- Display resolution of 0.1 mA
- Fully independent, precision current limit control
- 3 selectable modes of operation, including constant light output mode
- Adjustable compliance voltage
- Adjustable feedback gain, for photodiode feedback
- DC to 100 KHz voltage control/modulation port
- Safe output off/on switch
- Audible and visual fault condition indicators
- Optional GPIB/IEEE-488 interface
Output:
Current Range: 0 to 200 mA, floating
Compliance Voltage: 2 to >5 volats, adjustable
Temperature coefficient: <100 ppm/degrees C ambient
Noise and Ripple (@ 100 mA output):
< 11 uA, rms (HIGH BW mode)
<4 uA, rms (LOW BW modes)
Display:
Type: 4-digit LED display
Maximum Reading (output) 200.0 mA (Photodiode) 2.00 mA
Resolution: (output) 0.1 mA (Photodiode) 0.001 mA
Accuracy (25 degree C): (output) +- 0.2 mA (Photodiode) +-0.005 mA
Temperature Coefficient: (output) < 100 ppm/degree C (Photodiode) <100 ppm/degree C
Full manual can be downloaded from
http://hotsource.netnds.net/download/ILX_Lightwave_LDX_3207B_Manual.pdf
Web:
http://www.ilxlightwave.com/selection-guide/selection-guide-laser-diode-instrumentation.html#drivers
Some Photos:
All connected up with a laser load simulator.
Close-up on the display. The difference between the source current and measured is due to the point of current measurement.
The laser load is made up of resistors and LEDs.
Please PM me if interested.
Initially priced at thousands; now selling only at
[highlight]US$150 shipped[/highlight]
Check out the price when new! (>$1000)
Here are some of the specs:
- Intuitive front panel
- Highly visible green LED display
- Display resolution of 0.1 mA
- Fully independent, precision current limit control
- 3 selectable modes of operation, including constant light output mode
- Adjustable compliance voltage
- Adjustable feedback gain, for photodiode feedback
- DC to 100 KHz voltage control/modulation port
- Safe output off/on switch
- Audible and visual fault condition indicators
- Optional GPIB/IEEE-488 interface
Output:
Current Range: 0 to 200 mA, floating
Compliance Voltage: 2 to >5 volats, adjustable
Temperature coefficient: <100 ppm/degrees C ambient
Noise and Ripple (@ 100 mA output):
< 11 uA, rms (HIGH BW mode)
<4 uA, rms (LOW BW modes)
Display:
Type: 4-digit LED display
Maximum Reading (output) 200.0 mA (Photodiode) 2.00 mA
Resolution: (output) 0.1 mA (Photodiode) 0.001 mA
Accuracy (25 degree C): (output) +- 0.2 mA (Photodiode) +-0.005 mA
Temperature Coefficient: (output) < 100 ppm/degree C (Photodiode) <100 ppm/degree C
Full manual can be downloaded from
http://hotsource.netnds.net/download/ILX_Lightwave_LDX_3207B_Manual.pdf
Web:
http://www.ilxlightwave.com/selection-guide/selection-guide-laser-diode-instrumentation.html#drivers
Some Photos:
All connected up with a laser load simulator.
Close-up on the display. The difference between the source current and measured is due to the point of current measurement.
The laser load is made up of resistors and LEDs.
Please PM me if interested.
