Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

How to Register on LPF | LPF Donations

FS: Laser show parts

mattmagic100

mattmagic100

0
Joined
Feb 19, 2009
Messages
879
Points
18
Well, i dont think ill succeed in actually makin a laser show due to the time i dont have. So, ill just sell everything i have. =]

First off are the 2 70mm. 12V DC cooling fans. Asking for $5 shipped.(never used)


Second,(SOLD) is the 12V, 5A DC universal regulated switching power supply for the fan. (never used) payed $20, asking for $15 shipped.

Third, the 70mm fan grills. (never used) payed $3 shipped, asking for $1.50 shipped.


Fourth, the power entry module with fuse holder and switch. payed $6, asking for $4 shipped.(used in perfect condition except that prongs have been soldered(solder will be taken off as much as possible))


Fifth, a 10 foot DB25 female to DB25 male cable. Payed $12, asking for $9 shipped. (used but in perfect condition)


Sixth, (SOLD) a DZ breakout board. Payed $30, asking for $25 shipped. (used but in perfect condition).

Seventh, the galvos. These are CW20K scanning galvos with the drivers and power supply. Payed $145 shipped, asking for $120 shipped. (A little used)


Lastly!, a broken 100mW green laser with ttl modulation. something happened during one of the trials and the laser just went...."poof". :(
But i think all that is need to fix it is to replace the cmount diode inside. To check what was wrong, i had to unattach one of the optics. Will some thermal glue im sure itll go back on with no problem. :)
Payed $90, asking for $50 shipped. (pretty used;))





If you have any questions, PM and well get things movin :D

Thanks for looking!

Matt
 
Last edited:





robjdixon said:
Are the scanners ILDA or DMX?

Rob
Click to expand...

I'm sure others would know better than me, but I'd think they are neither - they are just the galvos and drivers, whichever DAC you use, or however you wish to drive it, will determine if it ends up an ILDA or a DMX system.
 
I'm pretty sure that some budget scanners can't run in ILDA mode; only in DMX
Rob
 
those amp boards are not what connect to your pc.
Ilda and dmx output the same signals just one comes from a pc the other comes from a memory chip on a board.
You need a digital to analog converter or dac.
This dac can be self running aka dmx or pc run.
 
All scan sets, regardless of cost, can be run via either DMX (with a DMX board, usually included) or ILDA if you wire the galvo amps inputs directly to a DB-25 connector using the ILDA pinout.
 
The pics are too large to see all at once. If they were 800 x 600, then I may be able to see what you're trying to sell there mattmagic100.

Thanks,

M
:)
 
Morgan said:
The pics are too large to see all at once. If they were 800 x 600, then I may be able to see what you're trying to sell there mattmagic100.

Thanks,

M
:)
Click to expand...

Crap im sorry i didnt realize they were so big.
I know this is a noob question but how do you resize them?

Thanks
 
N/P, here's what I do...

I use TinyPic - Free Image Hosting, Photo Sharing & Video Hosting , (thanks Flaminpyro for showing me that one!), and when you select the pic to upload from your pc, you can resize it to 800 x 600 as it uploads. Once it's uploaded you can choose the type of code, (there's a list of them. One says suitable for Forums or something but you'll see it); copy the code; and paste it in. Viola! Then, the pic just goes to full width on the screen without having to scroll left and right to read the text. With a large Avatar, you still have to scroll a touch but only once.

I hope that helps. PM me if I'm not explaining it well enough.

M
:)
 
You must log in or register to reply here.


Back
Top