jayrob
0
- Joined
- Sep 21, 2007
- Messages
- 9,862
- Points
- 113
(All SOLD)
I have 3 lasers that I am selling to make room in my cases. None of these lasers got much use at all. All three come with dust caps and batteries...
#1
This is a DX 'True Green' 30mW pointer. At normal room temperature, it starts out at around 24mW's and is over 30mW's with-in about 45 seconds warm up.
#1 - $20 bucks plus $4 dollars shipping. (U.S.) Includes 2 X AAA Energizer e2 Lithium batteries.
#2
This is one of my early builds before my current heatsink design. The module is 'pressed' in. The Sony/Senkat diode is putting out 202mW's through the AixiZ acrylic lens. It is a DDL driver with a 4.3 ohm resistor. (294mA's) The silicon diode and cap are at the diode. (The diode is one of the early ones, before the weaker batch that got replaced by the current diodes)
This never got much use, I built it, put it in the case, and kept building others... The front ring of the host was scratched, so I dressed it up a little to hide the scratch.
#2 - $55 dollars plus shipping. (inc. 2 X 3.6 volt rechargeable batteries)
#3
This was bought as a 30mW from DX. It starts out at 20mW's, and slowly climbs to over 40mW with-in 1 minute warm up. It reaches over 50mW's after about 1 1/2 min.
I did some slight modifications to this laser... I put the head in the lathe and drilled the plastic lens for a better beam and dot. I also put a clicky switch in the tail. (it came as a 'twist' on/off) Much better with a clicky.
#3 - $25 plus shiping. (inc. a 3.6 volt rechargeable battery)
If you want all 3, I'll pay the shipping! (if not in U.S. - no insurance) PM me if you are interested!
Jay
I have 3 lasers that I am selling to make room in my cases. None of these lasers got much use at all. All three come with dust caps and batteries...
#1
This is a DX 'True Green' 30mW pointer. At normal room temperature, it starts out at around 24mW's and is over 30mW's with-in about 45 seconds warm up.
#1 - $20 bucks plus $4 dollars shipping. (U.S.) Includes 2 X AAA Energizer e2 Lithium batteries.
#2
This is one of my early builds before my current heatsink design. The module is 'pressed' in. The Sony/Senkat diode is putting out 202mW's through the AixiZ acrylic lens. It is a DDL driver with a 4.3 ohm resistor. (294mA's) The silicon diode and cap are at the diode. (The diode is one of the early ones, before the weaker batch that got replaced by the current diodes)
This never got much use, I built it, put it in the case, and kept building others... The front ring of the host was scratched, so I dressed it up a little to hide the scratch.
#2 - $55 dollars plus shipping. (inc. 2 X 3.6 volt rechargeable batteries)
#3
This was bought as a 30mW from DX. It starts out at 20mW's, and slowly climbs to over 40mW with-in 1 minute warm up. It reaches over 50mW's after about 1 1/2 min.
I did some slight modifications to this laser... I put the head in the lathe and drilled the plastic lens for a better beam and dot. I also put a clicky switch in the tail. (it came as a 'twist' on/off) Much better with a clicky.
#3 - $25 plus shiping. (inc. a 3.6 volt rechargeable battery)
If you want all 3, I'll pay the shipping! (if not in U.S. - no insurance) PM me if you are interested!
Jay