Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

FS: 16X BDR-209 Burner For Sale.

M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
I'm selling this great 16x burner I just put together.
It is a BDR-209 with a G2 lense, a flexdrive v5 glued into the pill with arctic alumina, aluminum heat sink, and a really cool convoy s2 host. The host holds one 18650 battery (included.)
The driver is set at 600mA and between the heatsink and host, it stays very cool. It should last a long time at this power level. The burning pic is at over 4' burning white paper. This is an awesome laser!!
I've been on this forum for years, and have built and sold many lasers. I have just recently gotten back into the hobby. And I can't believe the power of this thing compared to the old PHR's I used to build!!
I'm asking $105 shipped in the States.

Thanks,
Jon
 

Attachments

  • IMG_1522.jpg
    IMG_1522.jpg
    71.4 KB · Views: 105
  • IMG_1524.jpg
    IMG_1524.jpg
    60.9 KB · Views: 95
  • IMG_1525.jpg
    IMG_1525.jpg
    67.9 KB · Views: 74
  • IMG_1526.jpg
    IMG_1526.jpg
    71.1 KB · Views: 67
  • IMG_1527.jpg
    IMG_1527.jpg
    61 KB · Views: 64
  • IMG_1528.jpg
    IMG_1528.jpg
    96.3 KB · Views: 86
  • IMG_1529.jpg
    IMG_1529.jpg
    63.7 KB · Views: 73
  • IMG_1523.jpg
    IMG_1523.jpg
    67.1 KB · Views: 99
Last edited:





BobMc

BobMc

0
Joined
Apr 23, 2016
Messages
3,685
Points
113
Nice little burner you got there. 600mAp's should get some long life out of your 209. Best wishes with your sale.

And welcome back to the hobby. :)
 
M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
Thanks guys!
The price can be negotiated as well. There just wasn't much comparable to price it against.
 
M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
Ok. This doesn't seem to be getting much attention. Let's drop the price to $105 shipped and I'll also toss in an 18650.

Thanks,
Jon
 
BowtieGuy

BowtieGuy

0
LPF Site Supporter
Joined
Oct 14, 2012
Messages
6,090
Points
113
Nice little burner you've built, morphs! :beer:

IMO, you've got it priced well, especially since you've included a battery, shipping, and a G-2 lens, not to mention that good looking Convoy host.
It's only been a couple of days, I don't think you'll have any problems selling baby soon. :)
 
D

dden4012

0
Joined
May 30, 2016
Messages
964
Points
0
I would like to see the heatsink. Really like the host. Is there enough room in the battery tube for 2 18350 flat tops?
 
paul1598419

paul1598419

0
Joined
Sep 20, 2013
Messages
17,414
Points
113
If it uses a boost driver, it wouldn't matter. Many of these do, so you need to be aware else you destroy the diode.

Never mind. I see that it doesn't.
 
Last edited:
D

dden4012

0
Joined
May 30, 2016
Messages
964
Points
0
paul1598419 said:
If it uses a boost driver, it wouldn't matter. Many of these do, so you need to be aware else you destroy the diode.
Click to expand...

Your right but this isn't why I'm asking. The 405 would end up in a pen build and I would probably throw a 520 in this host. Blues are great but I have enough burn marks on my walls and shelves. 520 just does it for me. The host looks great.
 
M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
I don't have any pics of the heat sink, unfortunately. But it's an aluminum "bushing" machined to 19mm. Od. 12mm. Id. And 20.5mm. Long. It's drilled and tapped with a set screw at the halfway point of the modules head. It was a tiny bit small in dia. So it's wrapped with a couple wraps of foil to make good contact with the host. I've ran this quite a bit and it transfers heat very well. As far as the batteries go, I'm not familiar with them. Are they the same or smaller diameter, amd half the length of an 18650? If so, I don't see why they wouldn't fit. If they're a little shorter it would be fine, because there are springs on bother the tail cap and the driver connection ends. And yes. It's a micro flexdrive v5.

Thanks,
Jon
 
Last edited:
M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
Ok. So I do have button top 16340 and two of them together measure 68.7mm. The host depth from the positive connection to the end of the tube(tail cap side) is 69.3mm. So I would say yes, they will fit. You might have to shorten one or both of the springs though.
 
Richie89

Richie89

0
Joined
May 9, 2015
Messages
1,181
Points
113
Dang man, 105 is a pretty darn good price. The G2 alone was probably 30 bucks! I may buy it soon if no one else does.
 
M

morphs

0
Joined
Dec 11, 2008
Messages
117
Points
18
Just to clarify, I'm pretty sure 3dlaserbuilder was referring to the arctic alumina adhesive I used to "fix" the driver in place. The way some might read his post would make it seem like I just half assed built this thing. It's a solid laser and I will guarantee the quality.

Thanks,
Jon
 
You must log in or register to reply here.




Top