Sparkles
0
- Joined
- Dec 21, 2010
- Messages
- 76
- Points
- 0
This laser includes the following features:
Black Maglite 2C host. As always, it is a side clicky on/off with the ability to do momentary on.
Dr. Lava's premier FlexMod P3 driver set to 1.8A. It is intended for labbies, so it is ultra high quality with diode saving features built into it.
2x18650 Sanyo Li-Ion 2400 maH batteries. This means the laser has 1 hour and 20 minutes of battery life before needing to recharge. Sanyo has the best batteries and reputation for Li-Ion batteries.
XJ-A140 diode, not the 130 diode.
Glow In The Dark dustcap. Its important to keep dust off the glass lens for a better beam.
Worlds smallest Li-ion charger: Cottenpickers Chargers. Provides TRUE CC/CV charge profile and non-trickle termination of charge to extend the life of the battery and keep the capacity high. It plugs into any USB port so you can bring the laser/charger with you where ever you go. Just need a computer.
MASSIVE aluminum heatsink.. HUGE! :evil:
Aixiz 445 glass lens. I prefer the lower cost and better beam profile of these lens.
I used Arctic Silver 5 to remove any possible air gaps on where the diode/module meet, the module/heatsink meet, and where the driver transistor/heatsink meet. Diodes hate heat build up, so I do to! Its worth the extra time to painstakingly apply thermal compound to the critical areas.
Just had one of my customers LPM a few of the lasers. Two of them Peaked 2W! :drool:
Suggested laser use cycle: 4 minutes on / 1 minute off.
The laser with everything included is $270 shipped (48 states) and is putting out 1.8W-2W. Everything is included except glasses. You DO need glasses and must purchase them separately.
TERMS AND AGREEMENT-
You are over 18 years of age.
- You understand that the laser and laser components that are mentioned above are dangerous when not properly assembled into a finished product.
- You will use the laser and components as an OEM product and properly incorporate them into a finished product.
- You will use these laser diodes in a safe and responsible manner and for a legal purpose.
- You are legally responsible for the use of these components, improper use of these components or their end products.
- You are legally responsible for any injury to anybody resulting from the use of or assembly of these components or their finished products.
- You accept this Laser as an OEM COMPONENT for integration in a system of YOUR OWN design and will be legally responsible from any and all LIABILITIES.
Legal Notice: The Laser Diodes and Modules are designed solely as an OEM component for incorporation into the customer's end products. Therefore, this laser does not and is not required to comply with the appropriate requirements of FDA 21 CFR, section 1040.10 and 1040.11 for complete laser products.
BY PURCHASING THIS ITEM YOU AGREE TO AND ACCEPT ALL THE PROVISIONS AND DISCLAIMERS IN THIS SALE FOR THE LASER PRODUCT.
:thanks:
Black Maglite 2C host. As always, it is a side clicky on/off with the ability to do momentary on.
Dr. Lava's premier FlexMod P3 driver set to 1.8A. It is intended for labbies, so it is ultra high quality with diode saving features built into it.
2x18650 Sanyo Li-Ion 2400 maH batteries. This means the laser has 1 hour and 20 minutes of battery life before needing to recharge. Sanyo has the best batteries and reputation for Li-Ion batteries.
XJ-A140 diode, not the 130 diode.
Glow In The Dark dustcap. Its important to keep dust off the glass lens for a better beam.
Worlds smallest Li-ion charger: Cottenpickers Chargers. Provides TRUE CC/CV charge profile and non-trickle termination of charge to extend the life of the battery and keep the capacity high. It plugs into any USB port so you can bring the laser/charger with you where ever you go. Just need a computer.
MASSIVE aluminum heatsink.. HUGE! :evil:
Aixiz 445 glass lens. I prefer the lower cost and better beam profile of these lens.
I used Arctic Silver 5 to remove any possible air gaps on where the diode/module meet, the module/heatsink meet, and where the driver transistor/heatsink meet. Diodes hate heat build up, so I do to! Its worth the extra time to painstakingly apply thermal compound to the critical areas.
Just had one of my customers LPM a few of the lasers. Two of them Peaked 2W! :drool:
Suggested laser use cycle: 4 minutes on / 1 minute off.
The laser with everything included is $270 shipped (48 states) and is putting out 1.8W-2W. Everything is included except glasses. You DO need glasses and must purchase them separately.
TERMS AND AGREEMENT-
You are over 18 years of age.
- You understand that the laser and laser components that are mentioned above are dangerous when not properly assembled into a finished product.
- You will use the laser and components as an OEM product and properly incorporate them into a finished product.
- You will use these laser diodes in a safe and responsible manner and for a legal purpose.
- You are legally responsible for the use of these components, improper use of these components or their end products.
- You are legally responsible for any injury to anybody resulting from the use of or assembly of these components or their finished products.
- You accept this Laser as an OEM COMPONENT for integration in a system of YOUR OWN design and will be legally responsible from any and all LIABILITIES.
Legal Notice: The Laser Diodes and Modules are designed solely as an OEM component for incorporation into the customer's end products. Therefore, this laser does not and is not required to comply with the appropriate requirements of FDA 21 CFR, section 1040.10 and 1040.11 for complete laser products.
BY PURCHASING THIS ITEM YOU AGREE TO AND ACCEPT ALL THE PROVISIONS AND DISCLAIMERS IN THIS SALE FOR THE LASER PRODUCT.
:thanks:
Last edited:
haha (I wonder how hard it would be to hide one this size from the wife?)