Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

Buy Site Supporter Role (remove some ads) | LPF Donations

Links below open in new window

FrozenGate by Avery

Cylindrical lens pairs, correction optics, anamorphic application

Joined
Jul 29, 2014
Messages
100
Points
18
Hello Guys! Special discound for LPF members comparing to Ebay price :)


Each lens pair is 65USD + 5 USD shipping worldwide.

For larger quantity a discount will be applied :)
If you have any question or need more info/photos, feel free to ask


dtbH3Vwl.jpg



First pair is dedicated for red Mitsubishi/Oclaro diodes, 1W 520nm NDG7475 and 3,5W 445nm NDB7A75 diodes.

Second pair is dedicated for 445nm popular diodes 1 - 2,5W and also works well with NDG7475 1W 520nm.




Lenses dimensions are 12mm x 12mm and 5-7 mm thick.
Lenses are AR coated for whole visible spectrum 400 - 700nm.
Extraordinary visible light transmittance >99,7% proved with AR test shown below.


E2OwLmfl.jpg


>99,3% light transmittance for whole pair!




Below there are photos with the results of measurements for several laser diodes.

Every photo was made at 10 meter distance between the wall and lenses.


Starring: First cylindrical pair and Oclaro HL63193MG 700mW 638nm:

nzZmtmYl.jpg


FN0I3yml.jpg




Starring: First cylindrical pair and Nichia NDG7475 1W 520nm:

QkWAiqcl.jpg


aULKzDZl.jpg




Starring: First cylindrical pair and Nichia NDB7A75 3,5W 445nm
I have only "after lens" shot, without lens the beam spot is almost the same as the Oclaro's one.

EebSpdGl.jpg






Starring: Second cylindrical pair and Nichia NDB7875 1,6W 445nm:

vYi3N92l.jpg


eMlD7Gxl.jpg




Starring: Second cylindrical pair and Nichia NDG7475 1W 520nm:

dbuDRvrl.jpg


koxvksCl.jpg



 
Last edited:





At what distance were the tests performed?

Also do you sell some sort of mount? How hard is it to align?
 
Distance from lens to the wall was 10m +-0,5m

It is harder than with anamorphic prisms, but also the output power is way better.

For the FIRST pair working with 3,5W 445nm mounted in my 4W laser module. The distance between the lenses is 19,5mm and the outside dimension for both lenses is 33mm.

Setting the lens:

1. U need to put one lens (concave) and see stright line, not bend line. This is the easiest. Also beam should be placed in the center of the lens, but this can be set approximately using eye. I'm doing it while the 10 minutes glue is drying.

2. Now you have really wide line on the wall. You need to take second lens and set it in 2 axis; turn and the distance between.
Distance between lenses is responsible for beam spot size.
Turn is responsible for S effect. I attach photo.
http://laserpointerforums.com/f49/c...inner-focus-ring-pix-91223-2.html#post1326382

When I was setting first pair I used just alluminium flat. But I found that it is easier when you have sry square,valley for the lens or just something glued on the plate to have stright line.

I already set around 4-5 pairs and now I think it is not very hard. But you need some patience wiht the first one ;)
 

Attachments

  • lens setting.png
    lens setting.png
    13.2 KB · Views: 392
  • lens setting2.png
    lens setting2.png
    5.2 KB · Views: 272
Last edited:
Ooh, how I do want.
The price would have to come down quite a
bit, though for me to be able to afford
I am seriously poor.
 
On ebay they are selling for 95 USD :P I will think about price drop but a bit later. They cost me a lot because of this AR coating.
 
I suggest offering this discount on PhotonLexicon- a lot of them are "projector guys" if you will, and the market for these lenses is much more prevalent over there.
 
I already made a thread, but I think I will make another one for group buy. Thanks for the info anyway :)
 
Well, when I receive my sample set....I will mount to the V7 versioin of the EZ mount. Will show a comparison between the A-prism's and C-Lenses. See attached pic.
I believe this design will work. Then we will go from there. Still looking for a Ally tube cover....not that this is needed for the optics to work, but a cover, clear acrylic or Aluminum will protect and help keep the optics clean.:D
 

Attachments

  • EZCA-CL-V7.JPG
    EZCA-CL-V7.JPG
    93.8 KB · Views: 698
Last edited:
Hi,
Please could you detail what lens are using as a collimator also Cylindricals EFLs?
By the spots sizes, I suppose its G2 or 3-elements... isn't it?
thanks!
 
Hi, I was using three element lens. This is why I show pictures before and after.

Cylindrical lens will always work the same no matter what lenses you use. Even if you use asphericsl 2mm EFL. It will just change the divergence x times and also make the beam wider at the output x times. This is why you do not need EFL of the cylindrical lens.
 
I know the concept of this is simple but would love to see a small tutorial with pics fitting them in the housing.

Wish there was some for the NMB44 450 nm 6w. I was just getting ready to grab another may hold off a while on that one
 
Last edited:
I know the concept of this is simple but would love to see a small tutorial with pics fitting them in the housing.

Wish there was some for the NMB44 450 nm 6w. I was just getting ready to grab another may hold off a while on that one


Please avoid digging up old threads. This thread was last posted to nearly 3 years ago.

Further, there's plenty of threads about correcting the NUBM44 with cylindrical lens pairs. Read through them to develop an understanding.

Here's one to get you started:

http://laserpointerforums.com/f49/o...enses-nubm44-beam-correction-tests-96445.html
 


Back
Top