grainde
0
- Joined
- Jan 29, 2012
- Messages
- 3,163
- Points
- 113
Hi guys this is my new FS thread for Sinner custom built lasers.:wave:
These are the hosts I have available.
Here you can see the copper pressed heat sinks used in these hosts![Smile :) :)](https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f642.png)
As I did previously with the grooves I will offer mirror polishing and GITD as options:
GITD* (Green, Blue, Aqua, Violet and Red): $ 10
Polishing: $ 20
Here are two new completed builds for sale; one with an NUBM07E diode and the other with an NUBM44.
Specs 465 5.8 W 07E
Sinner MS V1 host (new design) with focus ring
NUBM07E diode
Copper Module with extended copper back half
Lazeeerer SXD with pot set at 4 A and heat sinked directly to host
G lens
24AWG super flexible silicone wire
Takes 2 x 16340 batteries (not supplied)
SOLD
Please note Paypal fees applicable if payment not sent as F&F.
Specs 7 W 450 M44
Sinner MS V1 host (new design) with focus ring
NUBM44 diode
Copper Module with extended copper back half
Lazeeerer SXD with pot set at 4.5 A and heat sinked directly to host
G lens
24AWG super flexible silicone wire
Takes 2 x 16340 batteries (not supplied)
SOLD
Please note Paypal fees applicable if payment not sent as F&F.
Here you can see them both in action! They are both extremely bright and the 465 is actually ever so slightly more teal in colour than the camera shows it.
Notes: I dont actually know what the duty cycle of these lasers are, however as I prefer to look after my diodes, I generally stick to shorter run times to extend their lifetimes. As a guideline, I would recommend 1 min on and 1.5 mins off - at 1 min the head of the laser will be getting warm.
*I use the new generation of Europium doped GITD powders, which have very long glow times - even up to 10 hrs for the green and aqua!! The blue lasts for around 8 hours and the red and purple for around 1 hour.
For those of you not aware of multimode diodes the output is bar shaped and very similar to the M140 diodes ie not a tight dot.
** Note to buy a completed laser you must be over 18 and own the correct safety goggles for your chosen wavelength. Please feel free to PM me for further details. **
These are the hosts I have available.
![gmslLzB.jpg](http://i.imgur.com/gmslLzB.jpg)
![mUM31Dt.jpg](http://i.imgur.com/mUM31Dt.jpg)
![yjvA7aC.jpg](http://i.imgur.com/yjvA7aC.jpg)
![34o37VY.jpg](http://i.imgur.com/34o37VY.jpg)
![sFg0lbQ.jpg](http://i.imgur.com/sFg0lbQ.jpg)
Here you can see the copper pressed heat sinks used in these hosts
![Smile :) :)](https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f642.png)
![YknBpmc.jpg](http://i.imgur.com/YknBpmc.jpg)
![npj3ZRc.jpg](http://i.imgur.com/npj3ZRc.jpg)
As I did previously with the grooves I will offer mirror polishing and GITD as options:
GITD* (Green, Blue, Aqua, Violet and Red): $ 10
Polishing: $ 20
Here are two new completed builds for sale; one with an NUBM07E diode and the other with an NUBM44.
Specs 465 5.8 W 07E
Sinner MS V1 host (new design) with focus ring
NUBM07E diode
Copper Module with extended copper back half
Lazeeerer SXD with pot set at 4 A and heat sinked directly to host
G lens
24AWG super flexible silicone wire
Takes 2 x 16340 batteries (not supplied)
SOLD
Please note Paypal fees applicable if payment not sent as F&F.
Specs 7 W 450 M44
Sinner MS V1 host (new design) with focus ring
NUBM44 diode
Copper Module with extended copper back half
Lazeeerer SXD with pot set at 4.5 A and heat sinked directly to host
G lens
24AWG super flexible silicone wire
Takes 2 x 16340 batteries (not supplied)
SOLD
Please note Paypal fees applicable if payment not sent as F&F.
Here you can see them both in action! They are both extremely bright and the 465 is actually ever so slightly more teal in colour than the camera shows it.
![3Uv47SE.jpg](http://i.imgur.com/3Uv47SE.jpg)
Notes: I dont actually know what the duty cycle of these lasers are, however as I prefer to look after my diodes, I generally stick to shorter run times to extend their lifetimes. As a guideline, I would recommend 1 min on and 1.5 mins off - at 1 min the head of the laser will be getting warm.
*I use the new generation of Europium doped GITD powders, which have very long glow times - even up to 10 hrs for the green and aqua!! The blue lasts for around 8 hours and the red and purple for around 1 hour.
For those of you not aware of multimode diodes the output is bar shaped and very similar to the M140 diodes ie not a tight dot.
** Note to buy a completed laser you must be over 18 and own the correct safety goggles for your chosen wavelength. Please feel free to PM me for further details. **
Last edited: