Modules are back in stock
PLEASE READ EVERYTHING.
I am out of colored ink in my printer so i will still be sending the data log results via e-mail as for some reason it will not print in black and white so please also add the e-mail address you would like me to send the picture to via e-mail along with the other info requested bellow when attaching a note to the payment on PayPal.
Green laser modules with free shipping to members inside the US shipped from the US, no long shipping wait time from outside country vendors.
Laser modules run @3V with almost pure 532nm green output and very little IR output your getting what you pay for and not getting just 50mw in green with 100-150mw in IR output like some other cheap modules available.
Modules come with both battery spring bounce and two lead wires you can use either one and remove the other not used depending on your application, if needed i can remove one or the other for you prior to shipping upon your request. The modules also come with a on/off switch mounted to the board active when the spring bounce lead is used.
All modules will now be tested using a Laserbee IX for approximately 30-45 seconds from a cold start using a 3.3v wall power supply (about 3v when under load) and a decent size heat sink to prevent over heating. Results will sent via E-mail and attached as a picture for you to save and print out at your leisure, test will show the maximum output and average/resting output.
As my contribute to this forum website I will also donate to the forum to help keep it alive and show my apretiation for the use of this website for every laser module sold on this website $1 will be donated.
If you need me to send you an invoice with the amount for you to pay please PM me with your E-mail address that is linked to your paypal account.
:thanks:
Contact E-mail: EggMan1345@yahoo.com (contact me here for quicker responce time)
PayPal E-mail: EggMan54321@yahoo.com (please do not confuse with my contact email)
Please look below for the module you want to purchase it is a first come first serve, if you are ready to send the payment right away you can do so, please post a response with the laser module you paid for so other users know the module is already sold and not available anymore, i will try to remove and update the sold lasers are often as possible to also help avoid any mix up. please look through the post for sold lasers to make sure the laser you want to buy is not already sold before making a payment. You can send the payment without contacting me to make sure you get the laser you want without waiting for my response just look at the other post on this thread to make sure it has not already been paid for you sold, you can also contact me if you need help setting up a payment.
Test were ran for 30 seconds to 1 minute to find the resting output with a heat sink in use.
WHEN MAKING YOUR PAYMENT PLEASE MAKE SURE YOU LEAVE YOUR LPF USER NAME, THE NUMBER THAT CORRESPONDS TO THE MODULE YOU ARE PAYING FOR, THE LISTED OUTPUT AND PRICE. LEAVE THIS NOTE ON PAYPAY AND ATTACH IT WHEN SENDING YOUR PAYMENT.
THANKS
LASER MODULES IN SPEC AND THERE LPM RESULTS BELLOW
NUMBER MAX OUTPUT RESTING OUTPUT $$PRICE$$
1 SOLD
2 SOLD
3 Sold
4 SOLD
5 SOLD
6 SOLD
7 SOLD
8 SOLD
15 SOLD
Modules under spec sold at or below cost. I would normally send these back for replacement but this cost money for return shipping i will take a loss on the price and offer them to you and see if there is any interest. Some may have not had the current set right on the driver board from the factory i do not test the current draw when testing lasers so some of these you may be able to adjust, these are sold as is and expect to get the output results listed but if you know what your doing and can test the current draw you may be able to make some changes to increase the output im not responsible for anything you change if something goes wrong no refunds will be given, Modify or make changes at your own risk. You can check with other members for the average current draw but i think its around 700ma +/-
Module# MAX REST PRICE
10 126 106......$54.00
11 120 105......$54.00
12 108 85......$52.00
The modules bellow are FREAK modules, im not sure exactly what is wrong with them or what causes them to act as they do. They start off great from a cold start and hit power outputs that are to be expected from these modules but shortly after warm up 20-30 seconds the power drops dramatically to a low resting output. Im offering them at a cheap price like the ones above because of the way they act, this could be something with the power board or it could be a faulty diode i do not know enough about these to figure this out, if you want to use them as is for a project on a budget or know what causes this to happen and can fix it these modules are for you. If your worried about something being seriously wrong with them please do not purchase them as your aware of there odd behavior and i do not need any hassle. If anyone knows the cause and would like to fill me in i would be interested to know
# MAX REST PRICE
9 200 106...........$54.00 drops down after about 25 seconds
13 185 94............$53.00
14 195 88............$53.00
PLEASE READ EVERYTHING.
I am out of colored ink in my printer so i will still be sending the data log results via e-mail as for some reason it will not print in black and white so please also add the e-mail address you would like me to send the picture to via e-mail along with the other info requested bellow when attaching a note to the payment on PayPal.
Green laser modules with free shipping to members inside the US shipped from the US, no long shipping wait time from outside country vendors.
Laser modules run @3V with almost pure 532nm green output and very little IR output your getting what you pay for and not getting just 50mw in green with 100-150mw in IR output like some other cheap modules available.
Modules come with both battery spring bounce and two lead wires you can use either one and remove the other not used depending on your application, if needed i can remove one or the other for you prior to shipping upon your request. The modules also come with a on/off switch mounted to the board active when the spring bounce lead is used.
All modules will now be tested using a Laserbee IX for approximately 30-45 seconds from a cold start using a 3.3v wall power supply (about 3v when under load) and a decent size heat sink to prevent over heating. Results will sent via E-mail and attached as a picture for you to save and print out at your leisure, test will show the maximum output and average/resting output.
As my contribute to this forum website I will also donate to the forum to help keep it alive and show my apretiation for the use of this website for every laser module sold on this website $1 will be donated.
If you need me to send you an invoice with the amount for you to pay please PM me with your E-mail address that is linked to your paypal account.
:thanks:
Contact E-mail: EggMan1345@yahoo.com (contact me here for quicker responce time)
PayPal E-mail: EggMan54321@yahoo.com (please do not confuse with my contact email)
Please look below for the module you want to purchase it is a first come first serve, if you are ready to send the payment right away you can do so, please post a response with the laser module you paid for so other users know the module is already sold and not available anymore, i will try to remove and update the sold lasers are often as possible to also help avoid any mix up. please look through the post for sold lasers to make sure the laser you want to buy is not already sold before making a payment. You can send the payment without contacting me to make sure you get the laser you want without waiting for my response just look at the other post on this thread to make sure it has not already been paid for you sold, you can also contact me if you need help setting up a payment.
Test were ran for 30 seconds to 1 minute to find the resting output with a heat sink in use.
WHEN MAKING YOUR PAYMENT PLEASE MAKE SURE YOU LEAVE YOUR LPF USER NAME, THE NUMBER THAT CORRESPONDS TO THE MODULE YOU ARE PAYING FOR, THE LISTED OUTPUT AND PRICE. LEAVE THIS NOTE ON PAYPAY AND ATTACH IT WHEN SENDING YOUR PAYMENT.
THANKS
LASER MODULES IN SPEC AND THERE LPM RESULTS BELLOW
NUMBER MAX OUTPUT RESTING OUTPUT $$PRICE$$
1 SOLD
2 SOLD
3 Sold
4 SOLD
5 SOLD
6 SOLD
7 SOLD
8 SOLD
15 SOLD
Modules under spec sold at or below cost. I would normally send these back for replacement but this cost money for return shipping i will take a loss on the price and offer them to you and see if there is any interest. Some may have not had the current set right on the driver board from the factory i do not test the current draw when testing lasers so some of these you may be able to adjust, these are sold as is and expect to get the output results listed but if you know what your doing and can test the current draw you may be able to make some changes to increase the output im not responsible for anything you change if something goes wrong no refunds will be given, Modify or make changes at your own risk. You can check with other members for the average current draw but i think its around 700ma +/-
Module# MAX REST PRICE
10 126 106......$54.00
11 120 105......$54.00
12 108 85......$52.00
The modules bellow are FREAK modules, im not sure exactly what is wrong with them or what causes them to act as they do. They start off great from a cold start and hit power outputs that are to be expected from these modules but shortly after warm up 20-30 seconds the power drops dramatically to a low resting output. Im offering them at a cheap price like the ones above because of the way they act, this could be something with the power board or it could be a faulty diode i do not know enough about these to figure this out, if you want to use them as is for a project on a budget or know what causes this to happen and can fix it these modules are for you. If your worried about something being seriously wrong with them please do not purchase them as your aware of there odd behavior and i do not need any hassle. If anyone knows the cause and would like to fill me in i would be interested to know
# MAX REST PRICE
9 200 106...........$54.00 drops down after about 25 seconds
13 185 94............$53.00
14 195 88............$53.00
Attachments
Last edited: