Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Sony Announces new 405mn 100W laser

drumz0rz

drumz0rz

0
Joined
Jul 13, 2010
Messages
33
Points
8
Check this out guys. Sony and Tohoku University announce a new laser allowing for more blue ray storage. It's a 405nm laser that has acheived an output of greater than 100W! And people were worried about the 1W 445nm...

blue_violet_laser.jpg


I'm sure this tech is still a ways out from getting to consumers hands, but the first person to crack one open and put in in a host gets a prize.

In a press release, Tohoku University and Sony stated:

“This latest successful development is an all-semiconductor laser picosecond pulse source with a laser wavelength of 405 nanometers (1 nm = one-billionth of a meter) in the blue-violet region. It is capable of generating optical pulses in the ultrafast duration of 3 picoseconds (1 picosecond = one-trillionth of a second), with ultrahigh output peak power of 100 watts and repetition frequency of 1 gigahertz. Advanced control of the newly-developed and proprietarily-constructed GaN-based mode-locked semiconductor laser and semiconductor optical amplifier have enabled peak output power in excess of 100 watts to be achieved, which is more than a hundred times the world’s highest output value for conventional blue-violet pulse semiconductor lasers.”
Click to expand...
Link to full article: Sony and Tohoku University announce next generation laser for disks
 





Prototype

Prototype

0
Joined
Jun 19, 2009
Messages
2,710
Points
0
I can only see places with huge archives, like universities and large labs needing a pico-second 405nm laser. Cool find though, +1.
 
oic0

oic0

0
Joined
Jun 15, 2010
Messages
289
Points
0
Pretty awesome though wouldn't be much fun for a handheld. Would probably have a massive capacitor that could pop, not to mention you woudln't be able to see the beam. *Edit, oops didnt see the 1ghz, thought it was a single pulse. That would have some hefty power requirements wouldn't it?*

Did you guys see a while back where the military build a system that detects optics being pointed at its self and then blasts craters in the lens of the optics to render it useless with a femtosecond pulsed laser?
 
Last edited:
Trevor

Trevor

0
Joined
Jul 17, 2009
Messages
4,386
Points
113
I had a picosecond 100W 405nm laser once.

I hooked up a 450v 3300uF capacitor to a PHR. :crackup:

-Trevor
 
oic0

oic0

0
Joined
Jun 15, 2010
Messages
289
Points
0
Interestingly enough, easyhaz says it would only need OD of about 5.2
 
drumz0rz

drumz0rz

0
Joined
Jul 13, 2010
Messages
33
Points
8
Prototype said:
I can only see places with huge archives, like universities and large labs needing a pico-second 405nm laser. Cool find though, +1.
Click to expand...
Agreed, but what made it post worthy here is that SONY wants to use in in upcoming consumer Blu-Ray technology. Also, the fact that they could put this in a BD burner means it'll be small and able to run off a 12v source. The power requirement might hold it back from being a handheld but could easily be made into a lab type laser.
 
pullbangdead

pullbangdead

0
Joined
Aug 25, 2007
Messages
2,007
Points
63
3e-12 s pulse width, 1e9 Hz. That means .3% duty cycle at 100W peak, which gives a time-average power of 300mW. I believe it'd be easier for your laser pointer/tape burner to just use a 12x diode in CW mode if you're after tape-burning or visible beams.

Very cool science to be running these diodes mode-locked and such like they are, but really not too applicable to laser pointers at this time. It is awesome, but not in any "I can see the beam" or "it burns stuff" sort of way.
 
NobleKnight88

NobleKnight88

0
Joined
Jun 28, 2010
Messages
43
Points
0
Wallydraigle said:
Will this burn black electrical tape?
Click to expand...

Bahahaha! I was enjoying the good reads in this thread and you went and posted this. Nice.

I just don't get why they would need such a huge inscrease in output if to be used for consumer electronics purposes. If that even efficient?
 
Trevor

Trevor

0
Joined
Jul 17, 2009
Messages
4,386
Points
113
NobleKnight88 said:
I just don't get why they would need such a huge inscrease in output if to be used for consumer electronics purposes. If that even efficient?
Click to expand...

As burn speed and data density increase, the amount of time a point on a disc is over the laser assembly decreases. Therefore, more power. :)

-Trevor
 
mrbubl3s

mrbubl3s

0
Joined
May 11, 2010
Messages
142
Points
0
Why do they want to make it more dense? Isn't that bad for the long run?
 
Trevor

Trevor

0
Joined
Jul 17, 2009
Messages
4,386
Points
113
mrbubl3s said:
Well yeah, but, wouldn't that cause more errors too? :eek:
Click to expand...

...and other technology is keeping up with the increase in data density. The transition to Blu-ray seems to have gone fine. :whistle:

-Trevor
 
You must log in or register to reply here.




Top