Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

PHR w/Micro Boost Drive V1 cutting out.

awlego

0
Joined
Oct 9, 2009
Messages
160
Points
0
I built a homemade phr build in a flashlight using the new Micro Boost Drive V1. It is set at 135mA and worked great for several hours of use time over a couple of weeks. It lit matches almost instantly and was quite impressive... but now as soon as I turn it on it dims almost instantly to maybe half of the power it had before. It starts nice and bright, but after a half a second it dims - unable to light matches. I've tried new batteries, checked all my connections, made sure there was no shortages between the driver and the casing...

Any ideas what's going on?

Thanks,
-Awlego
 





Joined
Apr 26, 2010
Messages
4,175
Points
83
It MIGHT be because you ran it at 135ma...I was told 90 is 'conservative' 100 is safe, and 110-120 is pushing it....but 135? OUCH!
 

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
Recharge or replace your battery. Sometimes even "new" batteries have problems

If that doesn't do it, clean ALL your contact points again.

Diodes do NOT go brighter and dimmer and then brighter again if they are failing. This is a power source problem or the driver is having a problem

Peace,
dave
 
Last edited:
Joined
Apr 26, 2010
Messages
4,175
Points
83
Recharge or replace your battery.

If that doesn't do it, clean ALL your contact points

Peace,
dave

I thought that at first, but THIS made me think it had to do with the diode itself.

I've tried new batteries, checked all my connections, made sure there was no shortages between the driver and the casing...

BUT you should still double and triple check before assuming it's the diode, resoldering a connection is a lot cheaper than a new diode.
 

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
I thought that at first, but THIS made me think it had to do with the diode itself.



BUT you should still double and triple check before assuming it's the diode, resoldering a connection is a lot cheaper than a new diode.

Yes. "ALL" your connections includes solder joints. If it is a solder joint problem, it will be on the battery side. If it was on the diode side it should have blown the diode

Peace,
dave
 
Joined
Dec 23, 2008
Messages
3,948
Points
63
touching on what dave said. i don't know what batteries you are using but if they are cheap chinese rechargable lithiums it could be that. after the laser goes dim. tatke your batteries out and check each one with a multi meter. if it is less than a volt or two lower than the stated rating, it is a bad battery. happens to me all the time with the ultra fires.

michael
 

awlego

0
Joined
Oct 9, 2009
Messages
160
Points
0
Thanks for all the replies.

The diode is not blown, as Dave said. It works, it just has some power issues.

As for batteries, I'm using 3 triple A's. Using two different sets, the old set running 3.7 volts and the new set running 4.5 volts, the laser did the same thing. I'm pretty sure it's a driver issue as I get the exact same problem every time I power it up - all the while changing batteries or unscrewing the positive contact end cap. Every time it starts bright and then almost instantly goes to about half power. Maybe I'll take the driver off and set up my test load again and retake the voltage measurement and see what the theoretical amperage going through the diode is.

I will also take the module out and look at the driver and see if I damaged anything in my soldering... if it looks like I have, I do have another driver (but I hope I don't have to - I wanted to use it to build a different laser)

I'll post back when I have done this and let you guys know what's up. Thanks for the replies. Feel free to continue to add advice if anyone has experience/ideas on what may be going on.

-Awlego
 

daguin

0
Joined
Mar 29, 2008
Messages
15,989
Points
113
I'm still putting my money on a bad battery or connection

Peace,
dave
 
Joined
Apr 26, 2010
Messages
4,175
Points
83
wait...4.5V? I'm not expert, but don't micro-drives have a 2.25V dropout? Which means your drive is also only running on 2.25V (4.5-2.25 = 2.25)....I don't think that's enough, but I may be wrong...
 
Joined
Dec 23, 2008
Messages
3,948
Points
63
hey bloom. he is using a boost type driver. meaning it bucks the voltage up the necessary level. one more note on the flex drive, its maximum input voltage is around 5vdc.


michael
 
Joined
Apr 26, 2010
Messages
4,175
Points
83
hey bloom. he is using a boost type driver. meaning it bucks the voltage up the necessary level. one more note on the flex drive, its maximum input voltage is around 5vdc.


michael

Ooooohh...so that's what 'boost' in the name means...so if I give it 6V it will take everything it needs, but just use up the batteriesa faster? Same with 4.5V?
 
Joined
Dec 23, 2008
Messages
3,948
Points
63
6 volts is too much i believe. check in the instruction manual. but it is capable of boosting 3.5 volts up to 5.whatever for a blu ray for instance. they are good for compact builds where there is room for only 1 battery.

michael
 
Joined
Apr 29, 2008
Messages
1,562
Points
48
The micro boost driver is in fact a boost-only driver. So the input voltage has to be less than the diode's voltage. Try using a lower input-voltage, this may solve the problem.
 
Joined
Dec 23, 2008
Messages
3,948
Points
63
it depends on the which laser diode you are using and how many miliamps you will be running through it .


michael
 




Top