Welcome to Laser Pointer Forums - discuss green laser pointers, blue laser pointers, and all types of lasers

LPF Donation via Stripe | LPF Donation - Other Methods

Links below open in new window

ArcticMyst Security by Avery

Need help with wiring my blu-ray laser

bobhaha

bobhaha

0
Joined
May 31, 2009
Messages
3,239
Points
63
ok hey guys.. I have started a thread ages ago, but never got a straight answer... ok I have all the parts for my laser ready to go.. how do I wire all the parts together? do I have to make a jump with the ground pin on the diode?? do I just solder the wires from the positive pin to the driver and the same for the negative?? where do i put my momentary switch.. from positive batery terminal to driver or on negative....

Any thing else I have to know before i start soldering??????


Thanks in advance!! - Adrian
 





bobhaha

bobhaha

0
Joined
May 31, 2009
Messages
3,239
Points
63
Aixiz module on left, then driver (110ma Flexdrive), then momentary switch then battery holders

ssl17520.jpg
 
Last edited:
lasersbee

lasersbee

0
Joined
Sep 20, 2008
Messages
17,622
Points
113
Man.... by your question I can see that you have done absolutely no research
on the Forum at all...

It has only been 3 weeks ago that you asked a similar question and then again
1 week ago that members replied to... NOT ages ago.....

All the answers to putting your Blu-Ray build together has been posted on the
Forum umpteen times already...

Use The [Search ] button and help yourself..

Spoon feeding is for children....

I'll give you a starter hint....

1) attach the laser module to the driver
2) attach the driver to the batteries through the switch

For details.... research the Forum...


Jerry
 
Last edited:
Eku

Eku

0
Joined
Apr 14, 2009
Messages
448
Points
0
Pretty simple, solder + pin on diode to + on driver same with - then get the + and solder it to the switch and solder a wire onto the other pin and then connect the + wire from the switch to the battery holders + and wire the - from the driver to the - of the battery holders.

Oh and with the wires
Black = -
Red = +


Thats all you need to know.
 
bobhaha

bobhaha

0
Joined
May 31, 2009
Messages
3,239
Points
63
Thank you eku..

@Laserbee.. not to be disrespectful but i have tried the search button.. im not that dumb other wise why would i be posting this question.. and no one has simple explained it like Eku..

Btw Eku +rep man thanks for the help!
 
cust11

cust11

0
Joined
Jun 21, 2009
Messages
471
Points
0
*disclaimer*- opinion

You will be very disappointed with your build if you half-ass it and don't do any research. Half the point of building a laser is the DiY part, which is so much fun!

-Mike
 
Last edited:
cust11

cust11

0
Joined
Jun 21, 2009
Messages
471
Points
0
bobhaha said:
Aixiz module on left, then driver (110ma Flexdrive), then momentary switch then battery holders

ssl17520.jpg
Click to expand...

How are you sure that driver is set to 110mA? Did you dummy-load test it? Buying pre-set drives is ok but they should always be tested before using on a real diode. It would suck if your supplier got 2 drives mixed up and sent you a 300mA driver which would eat that PHR-803T in a second. Look, no one here wants to see you waste your money or be upset with your build. They do although, want you to do the research for yourself and not to expect everything to be laid out for you.

-Mike
 
bobhaha

bobhaha

0
Joined
May 31, 2009
Messages
3,239
Points
63
ok i understand thank you.. it was preset and current is printed on the board.. so yah..
 
You must log in or register to reply here.




Top